1
Real Firearms / Re: handguns for beginners
« on: December 04, 2013, 10:38:19 PM »
Anyways ill just leave it at that, do what you wish on the handgun, i wish you luck!
News:
Facebook might hate freedom, but it's still going strong here.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
Real Firearms / Re: handguns for beginners
« on: December 04, 2013, 05:47:46 PM »
Just one. Im pretty sure if a .22 can go through a ballistics vest it can pierce a heart. No im not being sarcastic. And i agree that the round itself is less intimidating, but in a bad situation, i doubt anyone is stopping to consider that its a .22.
3
Troubleshooting / Re: Anti-reversal latch wont fit new gears.
« on: December 03, 2013, 11:44:13 PM »
It wont be possible right now, but i can attempt to put them up tomorrow.
4
Real Firearms / Re: handguns for beginners
« on: December 03, 2013, 11:39:53 PM »
My question is that if it is just for defense, why does it have to be bigger than a .22? They can do the same deeds for less money. This is especially important if as you say, you arent confident with shooting one and is to be easy for your mom to use.
5
Troubleshooting / Re: Anti-reversal latch wont fit new gears.
« on: December 03, 2013, 11:11:47 PM »
M4, echo 1 platinum gearbox,mostly matrix internal mixed with some others. I tried shimming the latch for height and the gear is hitting the shims too. I have a bravo spur gear that does fit but is pretty worn and some stock g&g's somewhere at my other parents house. I assume you would recommend a working gearbox over spending too much time on a potentially flawed gear. But again any information helps.
6
Local Games Listing/RSVP / Re: Fox Company Presents; Operation: Renegade, October 19th | Current Registered: 31
« on: December 02, 2013, 11:30:16 PM »
Ha, i just looked back on this post for kicks and saw i "little man" ( chad didnt know my account) had won the pistol. Too late now.
7
Troubleshooting / Re: Anti-reversal latch wont fit new gears.
« on: December 02, 2013, 09:12:35 PM »
So i put it together to se if it would run, and it did. There was a strange grinding so i took it apart again, reassembled it and there is no noise now. I only have a 7.4 lipo to test with (which may be too high) and now it sounds like the gearbox may be reversing . I honestly dont know because ive never heard reversing before, but it takes another half second to what seems to be winding backwards. This is with shs 13:1 gears and a leftover matrix 3000. Could it be bad gears?
8
Troubleshooting / Anti-reversal latch wont fit new gears.
« on: December 02, 2013, 12:01:32 PM »
With the new gears i have put in my gun, the anti-reversal latch is scraping the spur gear and keeps it from running. Is it safe to run without the latch? Or will i have to scrap what i have? To be clear i do have it put together correctly.
9
AEG's / Re: Arm Mounted AEG Project
« on: January 17, 2013, 09:16:28 PM »
G&P usually makes good electronics. If your looking for real steel, the Z-bolt is often used in the military, but youll need a mount.
10
AEG's / Re: Is there a best for high speed gearing ratios?
« on: January 08, 2013, 09:22:33 PM »
Once again thank you. I only have a basic knowledge on internals, and really can only replace them. I would always love to learn , I hate not knowing how to do things myself.
11
AEG's / Re: Is there a best for high speed gearing ratios?
« on: January 07, 2013, 04:50:43 PM »
Thanks i really appreciate it. Another question, what motors do you prefer when going for high speed? I know a lot of people go for systema, matrix,g&p, and I know a couple running tienly. Is there a specific motor that would run best with the siegetek gears?
12
AEG's / Is there a best for high speed gearing ratios?
« on: January 06, 2013, 12:50:41 AM »
I want to build up a high speed m4 gearbox, but dont know what ratios are best for the internal gears. And also with a new setup , what brands are best and will i need a new pinion gear as well?
13
Airsoft Items FOR SALE / G&p stoner for sale
« on: June 19, 2012, 11:01:12 PM »
This was previously posted in the wrong area. I am selling my G&p mk23, for the reason that i realized i dont enjoy playing as support. I recently bought it for around 440 with coupons off evike. It is full metal except for the pistol grip , stock , and box mag. Also is v2 compatable with it currently shooting 412 consistantly. Has a rediculous hopup in case you wanted to use heavy bbs.i cant post pictures as i dont have a way of doing so but i can send some over text. Im looking to sell for $350 but will consider trades.
Have any questions or want pictures my phone number is 480-316-5034
I can meet at vangaurd
Have any questions or want pictures my phone number is 480-316-5034
I can meet at vangaurd
14
Airsoft Items FOR SALE / Re: Come check out this G36 grenadier. Post updated.
« on: May 24, 2012, 09:53:22 PM »
I assume the text is that big because you guys are 21+ 
15
Site Suggestions / Re: Entry Quiz
« on: May 24, 2012, 08:45:19 PM »
Thats what i was emplying, just in shorter detail.