1
Airsoft Items FOR SALE / Delete Thread
« on: October 31, 2011, 12:08:17 PM »
All equipment has been traded, sold. Thread can be deleted now.
News:
Facebook might hate freedom, but it's still going strong here.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Pages: [1]
2
Spring Power!! / Upgrading TM VSR-10 G-Spec
« on: June 25, 2010, 01:27:10 AM »
I currently came into possession of this rifle and am looking forward to upgrading it to the fullest potential. At the moment I have on my list of parts to purchase include the following
1x B↑Premier Palsonite Cylinder SET VC
-B↑Premier Palsonite Cylinder
-B↑Taper Cylinder Head
-B↑VC Piston
-B↑Spring Guide for VC Piston
http://www.x-fire.org/vsr_bup/e.bup_cylinder_vc_pal.html
1x Bore Up trigger set
http://www.x-fire.org/vsr_bup/e.bup_triggerset.html
1x 6.01mm PDI tight bore barrel
http://www.x-fire.org/etop/01.html
1x Firefly Hop Up Bucking for VSR-10 (Hard)
http://www.airsoftatlanta.com/Firefly_Hop_Up_Bucking_for_VSR_10_Hard_also_fit_p/63320.htm
From my understanding I need a different spring than the normal upgraded spring that would go with a VSR-10. I didn't have much luck unfortunately in finding anything on my own the last few days of looking through evike.com/airsoftgi.com/and trinityairsoft.com
I also did not find a bolt handle (saw a post on another site that it snapped while the shooter was cocking the gun but there were other reasons other than the resistance of the spring that caused it). I'm wanting this rifle to shoot decently far and be around 515fps with a .25g, but from what I understand I could have a higher spring with more hop up on the pellets to get better accuracy/range and keep it in that fps if few posts regarding the matter that I've read on here are correct.
I'm looking for any suggestions and would very much like the assistance on locating parts if it is not to much trouble.
Thanks again,
Hawkeye
Edit: found an aftermarket Hop Up finally
1x B↑Premier Palsonite Cylinder SET VC
-B↑Premier Palsonite Cylinder
-B↑Taper Cylinder Head
-B↑VC Piston
-B↑Spring Guide for VC Piston
http://www.x-fire.org/vsr_bup/e.bup_cylinder_vc_pal.html
1x Bore Up trigger set
http://www.x-fire.org/vsr_bup/e.bup_triggerset.html
1x 6.01mm PDI tight bore barrel
http://www.x-fire.org/etop/01.html
1x Firefly Hop Up Bucking for VSR-10 (Hard)
http://www.airsoftatlanta.com/Firefly_Hop_Up_Bucking_for_VSR_10_Hard_also_fit_p/63320.htm
From my understanding I need a different spring than the normal upgraded spring that would go with a VSR-10. I didn't have much luck unfortunately in finding anything on my own the last few days of looking through evike.com/airsoftgi.com/and trinityairsoft.com
I also did not find a bolt handle (saw a post on another site that it snapped while the shooter was cocking the gun but there were other reasons other than the resistance of the spring that caused it). I'm wanting this rifle to shoot decently far and be around 515fps with a .25g, but from what I understand I could have a higher spring with more hop up on the pellets to get better accuracy/range and keep it in that fps if few posts regarding the matter that I've read on here are correct.
I'm looking for any suggestions and would very much like the assistance on locating parts if it is not to much trouble.
Thanks again,
Hawkeye
Edit: found an aftermarket Hop Up finally
3
Troubleshooting / Spring Desert Eagle
« on: April 28, 2007, 06:28:19 PM »
When I had first started playing, the first gun I ever bought was this Desert Eagle
http://www.shortyusa.com/cart/viewitem.html?II=212&UID=1177809637-
I had been using it as a backup pistol early on and soon replace it with my current gas 1911. Before switching though, it had gotten a little roughed up while I was playing at one of the earlier Rebel Union Games. when I took it home, it wouldn't cock right so I decided to take a peep inside hoping it was just some sand blocking the slider. The moment I opened it most of the parts flung out and into the container that I had prepared incase that happened.
If anyone could be of help it would be greatly appreciated.
http://www.shortyusa.com/cart/viewitem.html?II=212&UID=1177809637-
I had been using it as a backup pistol early on and soon replace it with my current gas 1911. Before switching though, it had gotten a little roughed up while I was playing at one of the earlier Rebel Union Games. when I took it home, it wouldn't cock right so I decided to take a peep inside hoping it was just some sand blocking the slider. The moment I opened it most of the parts flung out and into the container that I had prepared incase that happened.
If anyone could be of help it would be greatly appreciated.
Pages: [1]