Airsoft Arizona

General Airsoft Arizona => Reviews => Topic started by: supporter on September 03, 2006, 11:16:18 PM

Title: VSR-11
Post by: supporter on September 03, 2006, 11:16:18 PM

The VSR-11 is a great starting sniper rifle. Stock, I was able to nail a 6' man about 250 feet away with .25s. It is spring, so nothing really special. There is "recoil", and it is about the same as a .22 rifle. It only costs about $100. According to the box, it shoots almost 300 with .2s. I have no idea what it shoots at with .25s, and since I am upgrading it, I will repost after Sand Storm.
I suggest this rifle to any new sniper, someone who wants something different, or someone looking for a good, cheap gun.

EDIT:Wrong rifle. Thanks Vince.

Title:
Post by: Vince on September 03, 2006, 11:16:55 PM

Are you sure it's not the USR-11 you have?

VSR-10s are more than $100.

Title:
Post by: frogguts198 on September 03, 2006, 11:33:02 PM

VSR-11's are only $100 springers.  I forgot which company makes them though.

Title:
Post by: supporter on September 03, 2006, 11:35:49 PM

according to the box, Lexair

Title:
Post by: Dammit! on September 11, 2006, 03:29:20 AM

well i have The hfc vsr11 so i bet thats the one you have. and yes it is a great gun. ive used it for alittle over three weeks now and not one problem. there is a little factory flaw with the mag though. it doesint jack the bb into the chamber unless you apply pressure to the mag by pushing it up into the mag well. and the rubber seal int the breach is VERY delicate.

Title:
Post by: supporter on September 22, 2006, 09:02:29 PM

New update on this review:

I put a 150 spring in it, and when i tried the crono at JT, it shot 480 fps with .2s. I still think for a springer, 480 is damn good.

Title:
Post by: gearbox on September 22, 2006, 09:51:22 PM

Quote from: "supporter"

New update on this review:

I put a 150 spring in it, and when i tried the crono at JT, it shot 480 fps with .2s. I still think for a springer, 480 is damn good.

Did you have to replace anything else along with the spring (for durability, etc.)?  Also, I read a review on Arnie's where the guy   mentioned feeling a fairly largre amount of unexplainable resistance every so often when either drawing the bolt back or pushing it forward. Have you experienced any of this?

Title:
Post by: supporter on September 23, 2006, 06:36:40 AM

I didnt replace anything else, and I wouldnt be able to tell you about the resistance, because my scope is in way of the bolt, so I always have a little bit of resistance. As of yet, no, no unexplainable resistance as of yet.

Title:
Post by: mick3355 on June 04, 2007, 11:37:27 AM

I bought this rifle a week ago, and i have not have had 1 chance so far to even loading it. From the moment i took it and tried to pull the lever, i have been trying to figure out what the problem is, but it seems my cylinder is stuck in a mysterious way.
I can't find similar problems anywhere, and have no idea how to get my cylinder to move. I can't pull it back to load a normal shot, i can't remove the cylinder if i press the little button down. The lever just doesn't move backwards. I can only twist it up and down.
Does anyone have an idea what it could be and what i should try to figure the problem?

Title:
Post by: mick3355 on June 04, 2007, 11:48:28 AM

srry that i posted this in the review section, i'll post it again in the troubleshooting section.