Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dannerson

Pages: [1]
1
Airsoft Items FOR SALE / Re: G and p magpul body + polarstar sr47
« on: September 17, 2014, 06:34:08 PM »
Bump for David.

2
Local Games Listing/RSVP / Re: Wild West paintball saturday the 15th
« on: March 12, 2014, 12:13:42 PM »
I will most likely be there.

3
Troubleshooting / Re: Locked gearbox
« on: March 11, 2014, 01:57:59 PM »
Does the pinion gear from the motor mesh well/properly to the bevel gear? Being a Matrix / evike motor I've read a few things about them not meshing. Could eliminate this by putting your stock motor in to see if I cycles.
You could also check the bevel gear shimming to pinion if it's to tight that could cause the problem too. I know when I first started I was over shimming a little because I wasn't closing the GB with the screws to check my shimming I was just using my hands to pinch it closed.

Throwing this out there. The other thing to check for is burr on the tappet plate. I'm not sure how stiff the A&K tappet plates are but if they are floppy could be a factor. Flicking up from the selector gear to the piston rack. Stiffer tappet and a selector delay clip.

4
General Off-Topic Discussion / Re: What do you guys do for a living?
« on: March 06, 2014, 09:40:10 AM »
Electromechanical Engineer / Apprentice Mad Scientist

5
Troubleshooting / Re: Locked gearbox
« on: February 26, 2014, 08:20:06 PM »
Other than the motor and spring is everything else stock?

I had a similar issue but I was able to find the issue was related to the shs/core gears were slight larger in diameter / selector gears for the piston rack were slightly larger/wider

6
General Airsoft Game Discussion / Re: Looking for possible field near Queen Creek/S.T.V.
« on: February 24, 2014, 01:38:35 PM »
Only legit field in that area is Wild West.

7
AEG's / Re: G&G TR15 Raider-L vs Lonex M4-A1
« on: February 24, 2014, 11:57:58 AM »
I have no first hand experience with the A3 but from what I have read it is a high speed motor. In general high speed motors are pretty pointless. Most field guns run a 110-120 spring and a high torque motor can handle those extremely well with increased rof while the high speed might be able to pull those springs it would suffer lower rof.

Exception to the high speed motor nomenclature would be the SHS High Speed.

To the point the A1 or A2 would be a better choice. Also the AMP 5000l is very good and $10-20 less.

8
Local Games Listing/RSVP / Re: Wild West Paintball and Airsoft!
« on: February 24, 2014, 11:01:25 AM »
Only one near a church in the east valley that I knew of was off Crimson Road and the US60 but as others had said they shut it down. It's now a parking lot back there.

9
Local Games Listing/RSVP / Re: Wild West Paintball and Airsoft!
« on: February 24, 2014, 07:33:52 AM »
Yah the 4 of us. Tried calling a few other to see if they would join but no luck. Still had fun. The guy in the sales shed said Saturday has better turnouts than Sunday for airsoft.

10
Real Firearms / Wts Lee Single Stage Bullet Loading Press
« on: November 01, 2013, 03:20:16 PM »
Hi AA,
I have a Lee Champion Single Stage (not progression/turret) Kit I got a while ago when the ammo crisis occurred with the impression I would start loading my own ammo. While the idea is a good one I just done have the time or space to do it. It hasn't been used and is in new condition with all the original items and accessories; box too.

This kit includes
Lee C frame single stage press with quick change bullet collets (2 collets)
Hand Priming Tool
Operating Manual
A set of Lee 30-30 carbide loading dies with original box never used either.

I would like to get $80 for this. The press was $110 and the dies where $35 so it's a steal.
I would look at trades for airsoft related items but no low end stuff.
JG anything V2 Nd decent shape, ics m4/16 (I would add depending)

11
Airsoft Items FOR SALE / Re: WTT/WTS G&G Combat Machine M4 CGB-S Gas Blowback (GGBR)
« on: May 29, 2013, 08:13:55 AM »
Thank you for all the offers. It has been traded off.

12
Airsoft Items FOR SALE / WTT/WTS G&G Combat Machine M4 CGB-S Gas Blowback (GGBR)
« on: May 26, 2013, 12:42:20 PM »
I just got into airsoft an went with a mystery box from online. I was hoping for a pistol or an aeg vs a GGB rifle.

This is a new in box never used.

This is the description from online.

Specifications:
Manufacturer: G&G
Model: M4 Carbine GBBR
Muzzle Velocity: 420-430 FPS
Magazine Capacity: 40 rounds
Color: Tan
Package Includes: Gun, magazine, manual

Features:
High quality polymer receivers
Front and rear sling points
Closed bolt gas blowback system
Adjustable LE stock

I would totally keep this gun if it was for the price of the mags. Being my first airsoft piece i dont want to spend an additional $200 for 4 mags.

Trades I would be interested in:
GGB pistol - M9, 1911, cz75, Glock
AEG M4
AEG Sig 552, 556
(Any of decent quality aeg that has mid cap mag options)

Cash price, $130.
I know these sell online for $140 + shipping and I'm asking a bit less. It's new never used.

13
Introduce Yourself! / Re: New Guys, Please Read! Make your first posts here!!
« on: May 26, 2013, 11:30:54 AM »
Hello, names Danny. Arizona native, born and raised since 84'. I currently live in san tan valley. I have no mil or LE experience. Have been shooting real steel competitions since I was 10 yrs old(CMP High Powered rifles, IPDA, etc.). Could say I'm a mil junky. Went paintballing when I was 16 did that for years but its to expensive and not really a tactical training.
I a friend got me into airsoft a few months ago and had been using his spare gear up to now. I got a mystery box from online to start off.

Look forward to meeting up with some fellow others or teams to run a few games.

Thank you,
Danny

Pages: [1]