Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Zanurath

Pages: [1] 2
1
General Airsoft Discussion / Re: Reliability of G&P
« on: July 13, 2018, 02:08:58 PM »
I have had one for about 6 years, the piston will go out at some point and replacing with full metal teeth will have it run forever I would also recomment a spring guide upgrade since (at least of the ones 6 years ago) they used a metal ring that just sits on the base of the guide to simulate a ball bearing spring guide and that ring can come loose and catch the spring or piston. I also burnt out a trigger but thats because I ran an 11.1 without a mosfet on it but all things considered mine shoots very well decent ROF and good reliability other than the 2 little things mentioned above.

2
AEG's / Re: Is it worth it to switch to Lipo
« on: June 10, 2018, 10:49:14 PM »
Yes, you can even put them on AEGs with no fet (7.4 only) they do better with outside temp changes and they have higher amperage (better trigger response). only downside is they can be ruined if drained too low and are more dangerous if you do something stupid. I have 2 9.6 batteries I still use because they are old and refuse to die but I never purchase new ones either getting high maH/C rating 7.4s or good 11.1s (with a good mosfet).

3
General Airsoft Discussion / Re: BB questions
« on: May 22, 2016, 05:57:51 PM »
This all really depends on your role and your weapon with my high rate of fire M4 ill go through 3000 BBs in a day but as a marksman with a longer range gun ill go through 400-500 in a day

4
When I looked it up it seems to come with the orange tip being metal and threaded anything you might attach will be tight because of the paint on top of the threading but it should still work with anything threaded 14mm- I have a similar one and if you twist the orange tip it isn't very firmly attached and you can take off the treaded tip and replace the orange painted one with an unpainted one ( I believe Evike stocks them) if you don't like having to crank it through the paint

5
Post the gun its not always the same. WE Tech makes quite a few 1911s

6
AEG's / Re: G&P rapid fire 2 VS ARES amoeba mr/e-sd
« on: November 17, 2015, 12:51:02 AM »
The G&P will be usable for both right out of the box without needing to buy a second spring or open up the gun but the ARES has a programmable FCU for bursts and such. That aside my favorite would probably be http://www.evike.com/products/49144/ its that ARES but longer Modular rail so you can also have a more forward and stable grip. Before buying online check with Command Post its a local shop I know use to have some and when I saw them they were offering to use their programmer (doesn't come with gun) to program the fire modes if you buy it there.

Happy airsofting

7
Airsoft Items FOR SALE / G&P m4 Custom
« on: August 27, 2015, 10:21:37 PM »
Have a green G&P with upgraded compression (everything north of the gears replaced) 509 steel 6.03 barrel mock suppressor and RIS. Including a battery scope and foregrip with it. Cant figure out how to post pics on here so message me an email or phone number and I will send pictures. looking for $400 cash or an upgraded Masada

8
General Airsoft Discussion / Re: Sniper Help
« on: February 27, 2015, 07:45:55 AM »
Most AEGs can get amazing range especially if they are v2.5 gearbox like the SR-25 but if you do want an actual bolt action sniper then gas would be my recommendation.Polarstar engines for AEGs are also a great alternative if you have the money.

9
Airsoft Items FOR SALE / Re: Green G&P upgraded for sale
« on: November 21, 2014, 10:04:35 PM »
Bump still have it all

10
Airsoft Items FOR SALE / Re: Green G&P upgraded for sale
« on: November 12, 2014, 03:06:46 PM »
KA short aluminum QD M203 with two KA 120r shells if you have a P* rig (engine/line/reg)

Will do the launcher 1 shell and a G&G C02 GBB m9 for a A&K masada (doesnt need to be running but no broken externals)

11
Airsoft Items FOR SALE / Re: Green G&P upgraded for sale
« on: November 05, 2014, 01:59:36 PM »
Added info the for the compression updates
CNC aluminum ported piston full steel rack (almost same weight as polycarb with full metal but much more durable)
CNC Aluminum posted piston head
Chrome full cylinder
double O ring nozzle
Just added larger O rings to the cylinder head (it was fine to begin with but just added better seal while it was open)

Forgot to add that the bucking was a aftermarket King Arms bucking for 400fps (G&P buckings tend to be a little soft stock)

Will leave the 4x compact scope and the foregrip on if if its bought

If you have a reasonable offer just PM me I'll consider anything interesting in airsoft for trade or partial trade (will add some more to trade for a P* engine or engine/reg/line setups)

12
Airsoft Items FOR SALE / Green G&P upgraded for sale
« on: November 01, 2014, 10:32:19 PM »
Rear wired to deans with 9.5inch CNC aluminum RIS. Has the whole compression part of the gearbox upgraded and a 509 stainless steel barrel with a 150mm CNC aluminum black mock suppressor has the original front post sight with a flip up rear sight. Original G&P motor has good rate of fire so that was left alone looking for $400 or so cash or a A&K masada (must be the one with version 2 gearbox) and some cash. Can't figure out how to post pics on here but can provide them if you're interested through text or email.

Comes with a 9.6v butterfly battery that goes in the stock

13
Airsoft Items WANTED / 9.5 inch barrel
« on: October 07, 2014, 10:54:31 AM »
Hey guys I'm looking for a 9.5 inch barrel 14mm+ I currently have a 9.5 but it's 14mm negative and I need th3 positive threading. This is for a m4 AEG. Meeting some were near command post would be great (I belive the barrel I have is machined aluminum 2 piece barrel)

14
Airsoft Items FOR SALE / Re: Echo 1 MRF MX Dmr FS/FT
« on: September 04, 2014, 12:08:05 PM »
I have a 7" regular RIS that I can do instead but its black not the foliage green of the gun

15
Airsoft Items FOR SALE / Re: Echo 1 MRF MX Dmr Build
« on: September 03, 2014, 05:48:19 PM »
Would you trade for a green G&P with 509 barrel and mock suppressor. Has a new bucking, nozzle, cylinder, piston, and piston head upgraded aside from the barrel and a S-System CNC aluminum RIS. Would come with a K.A. m203 and KA 120r Shell. not sure how to upload pics on here but can text some or email them to you if you want.

Pages: [1] 2