Author Topic: Nukefets, Nukefet Completes, Tactical Nukefets  (Read 3239 times)

Offline nukeduster

  • Trade Count: (+8)
  • Sergeant Major
  • *****
  • Posts: 713
    • View Profile
Nukefets, Nukefet Completes, Tactical Nukefets
« on: February 28, 2015, 05:04:23 PM »
Over 2000 sold worldwide!

www.nukefet.com

All NukeFets (Nukefet Original, Tactical Nukefet, Nukefet Complete) are hand soldered and assembled in America by an American US Army Veteran.

They are designed to be affordable, reliable, compact, and have the capability to increase your rate of fire (depending on several factors), while using premium quality parts designed to tolerate demanding builds.


NOTE: Please only use batteries rated for at least 20A discharge. The product works with
7.4v batteries(minimum), but if you are using it in a high performance AEG, please consider using an 11.1v
battery instead.
You can calculate your battery's discharge rating by taking your batteries "c" rating, and
multiplying it by your mAh rating / 1000.
For example a 20c, 1500 mAh battery would be rated for 20 x 1500 / 1000 = 30A.


Nukefet:





The NukeFet is capable of handling some of the most demanding airsoft builds imaginable! The
key to its power comes from its International Rectifier 3034 mosfet. I only used RoHS compliant
name brand components, no Chinese cheap knock offs or factory seconds. I mostly use
Panasonic, Infineon, and International Rectifier parts.

I use 16 gauge Alpha Wire primary wires and 24 gauge Alpha Wire secondary wire. This is some
of the best wire available on the market, and it isn’t cheap!


The NukeFet comes with approximately 18" of wire on the battery side, and 18" of wiring on
the drain side, 2 gold plated Lonex OEM motor connectors, a Deans Ultra style male
connector, and 4 pieces of heat shrink for the motor and battery connections.
The NukeFet now uses even thinner 16awg Alpha Wire! The OD is 1.96mm. The previous wiring
OD was 2.34mm.
Rated for 12.8v maximum.



NukeFet Complete:




The NukeFet Complete is a standard NukeFet which has been hand soldered and assembled,
and requires no soldering skills to install.

The NukeFet Complete is compatible with most v2 rear wired configurations. It was designed
and tested to work with many G3, MP5, M4, M16 configurations but should work with other
rear-wired v2 installations as well.

Please check that the following measurements are compatible with your AEG before
purchasing.


When installed, the wire measurements are (approx.) as follows:

Positive motor wiring: 4.8" (plus motor connector)
Negative motor wiring: 4.6" (plus motor connector)
Back of gearbox to mosfet: 5.7"
Back of gearbox to battery connector: 12"
Rated for 12.8v maximum.




Tactical Nukefet:





The Tactical NukeFet differs from the standard NukeFet, by being able to take even MORE abuse. The Tactical
Nukefet is rated for 20v (normal NukeFet is rated to 12.8v officially) and can tolerate an
additional 50 amps over the standard NukeFet (and all other traditional 3034 based
MOSFETs)! Want to run a 5s (18.5v) LiPo on a 700 fps 30 RPS gun? Done. Want a
Gatling cannon with a custom gearbox and run it off of a car battery? Done.
This MOSFET will tackle (almost) any AEG you can throw at it.

Comes standard with approximately 18" of 14awg (2.31mm Outer Diameter) Alpha Wire
on each side of the MOSFET, 18" of additional 14awg Alpha Wire, 4 gold plated Lonex
OEM motor connectors, a Deans Ultra style male connector, and 4 pieces of heat shrink
for the motor and battery connections.


Rated for 20v maximum.



All prices are plus $5 flat rate shipping, regardless to the # of fets you order.
« Last Edit: May 06, 2015, 07:02:33 PM by nukeduster »